Canada: The AL 7000 is here!

myproduct

AL-7000 is a hand held, portable breath alcohol tester to
check subject's breath alcohol concentration with reliable accuracy.

BUY NOW

Technical Specification

Press and hold the power button under LCD, and the number "7" will be displayed then will count down to "2".

2. After the digit "2"is displayed, the LCD will blink and beep. The numbers will be displayed again from "9" to "0"(Take your finger off the button from the digit "9")

3. The digit "0" will be displayed for 3 seconds, then blow into the inhaler between 3~4 seconds, and then the tester will switch off automatically. (This process is for inputting each body condition in advance, not for measuring the user's alcohol level)

4. In order to obtain a more accurate result, you should calibrate twice.

To Check Gas Leakage

    1. Press and hold the power button under LCD, and the number "7" will be displayed then will count down to "2".

    2. After the digit "2"is displayed, the LCD will turn blank and beep. The display will show the digit "9" and will count down to "0"

    3. The digit "0" will be displayed for 3 seconds, and the power will automatically turn off.

    4. In order to obtain a more accurate result, you should calibrate more than once.

2. Testing

To Check Alcohol Consumption

    1. Press the power button under LCD for 2 seconds, and the following numbers, "7" to "0" will be displayed and beep.

    2. After the beep, blow immediately into the tester for 3~4 seconds, Exhale a consistent amount of air each time and at the same angle.

    3. The number "0" will blink for about 3 seconds and then the test result will be displayed along with a beep sound on the LCD. The electric power will automatically shut off.

    4. In order to obtain a more accurate result, you should use the tester repeatedly 2~3 times.

To Check Gas Leakage

    1. Press the power button under LCD for 2 seconds, and the following numbers, "7" to "0" will be displayed and beep.

    2. When the number "0"on the LCD is displayed, a beep will sound. The product will test for any gas in the atmosphere.

    3. The number "0" will blink for about 3 seconds and then the test result will be displayed along with a beep sound on the LCD. The electric power will automatically shut off.

    4. In order to obtain a more accurate result, you should use the tester repeatedly 2~3 times.-->

    1. Indication of B.A.C.: (Full 3 decimals)
    0.000 to 4.000
    or 0.000 to 4.000
    or 0.000 to 0.400%BAC by LCD display
    2. Warm up time : within 25 seconds
    3. Response time : within 3 seconds
    4. Sensor : Semiconductor type alcohol sensor
    5. Use mouthpiece
    6. Power : Two 1.5V "AA" size alkaline battery and 12V cigar jack in car
    7. Continuous using time without battery change : 200 times with fresh batteries
    8. Weights : 103g (Including Batteries)
    9. Dimension (mm) : 116 (height) X 50 (width) X 21 (thickness)
    10. Audible warnings : 3 steps beep warning of alcohol detection with LED display
    11. Auto power off
    12. Accuracy : +/-0.010%BAC at 0.050%BAC
    13. Remark
    1) Battery low indication
    2) Air flow rate checking
    3) Self sensor testing
    4) EASY to replace the sensor

    Certificated CE

Contents

- AL-7000 : 1pc
- AA size Alkaline Batteries : 2ea
- 12V cable : 1ea
- Mouthpiece : 5pcs
- Pouch : 1pc
- Hand Strap : 1pc
- User's Guide

Caution !
  • This product should be used only to give an indication of the possible presence of alcohol in the blood. Do not use it to determine intoxication or whether it is safe to drive a vehicle or operate equipment! This product is just for your reference. This detector assumes no liability for the result of alcohol use.
  • Do not use it while drinking or smoking. (Measuring alcohol level at least 30 minutes after consuming alcohol)
ajax
ajax